For the first time in Australia, researchers from University of Melbourne and Monash Institute of Medical Research have converted diseased skin cells into stem cells. Researchers have completed the study by using skin biopsies from patients with the rare genetic disease Friedreich Ataxia (FA). The discovery will allow for the development of new treatments for FA and related conditions such as diabetes and heart disease. For more information, see the following websites: University of Melbourne Stem Cell Laboratory: www.cns.unimelb.edu.au Monash Institute of Medical Research: www.monashinstitute.org Friedreich Ataxia Research Association: www.fara.org.au Friedreich Ataxia Research Alliance: www.curefa.org Produced by Rebecca Scott Camera by Clive Banfield Editing by Rob Cross, Corporate Video Video of heart cells provided courtesy of: Duncan E Crombie Senior Research Assistant Stem Cell Medicine, O’Brien Institute With thanks to: Dr. Alice Pébay Group Leader, Stem Cell Lab Centre for Neuroscience and Dept of Pharmacology The University of Melbourne Senior Research Fellow, O’Brien Institute Dr Mirella Dottori Group Leader, Stem Cell Lab Centre for Neuroscience and Dept of Pharmacology University of Melbourne Dr Paul Verma Senior Scientist, Head of the Reprogramming of Somatic Cells Lab Centre for Reproduction and Development. Monash Institute of Medical Research Dr Jun Liu, Post-doc fellow Centre for Reproduction and Development. Monash Institute of Medical Research Ms …

2010_201002_20100211_161853_38


Image by ekurvine

ZoneTag: Photosphere / About. Owner only: Fix Location / Add Tags / Settings

Related Facebook pages

steam cells pages

Related Twitter topic

steam cells topics

Related Flicker images

steam cells images

Related youtube videos

steam cells videos

The word is derived from the Greek πλαστικός (plastikos) meaning fit for molding, and πλαστός (plastos) meaning molded. It refers to their malleability, or plasticity during manufacture, that allows them to be cast, pressed, or extruded into a variety of shapes—such as films, fibers, plates, tubes, bottles, boxes, and much more.

The common word plastic should not be confused with the technical adjective plastic, which is applied to any material which undergoes a permanent change of shape (plastic deformation) when strained beyond a certain point. Aluminium, for instance, is plastic in this sense, but not a plastic in the common sense; in contrast, in their finished forms, some plastics will break before deforming and therefore are not plastic in the technical sense.

There are two types of plastics: thermoplastics and thermosetting polymers. Thermoplastics will soften and melt if enough heat is applied; examples are polyethylene, polystyrene, polyvinyl chloride and polytetrafluoroethylene (PTFE). Thermosets can melt and take shape once; after they have solidified, they

Plastics can be classified by chemical structure, namely the molecular units that make up the polymer’s backbone and side chains. Some important groups in these classifications are the acrylics, polyesters, silicones, polyurethanes, and halogenated plastics. Plastics can also be classified by the chemical process used in their synthesis, such as condensation, polyaddition, and cross-linking.

Other classifications are based on qualities that are relevant for manufacturing or product design. Examples of such classes are the thermoplastic and thermoset, elastomer, structural, biodegradable, and electrically conductive. Plastics can also be classified by various physical properties, such as density, tensile strength, glass transition temperature, and resistance to various chemical products.

Due to their relatively low cost, ease of manufacture, versatility, and imperviousness to water, plastics are used in an enormous and expanding range of products, from paper clips to spaceships. They have already displaced many traditional materials, such as wood; stone; horn and bone; leather; paper; metal; glass; and ceramic, in most of their former uses.

The use of plastics is constrained chiefly by their organic chemistry, which seriously limits their hardness, density, and their ability to resist heat, organic solvents, oxidation, and ionizing radiation. In particular, most plastics will melt or decompose when heated to a few hundred degrees celsius. While plastics can be made electrically conductive to some extent, they are still no match for metals like copper or aluminium.[citation needed] Plastics are still too expensive to replace wood, concrete and ceramic in bulky items like ordinary buildings, bridges, dams, pavement, and railroad ties.

Chemical structure
Common thermoplastics range from 20,000 to 500,000 in molecular mass, while thermosets are assumed to have infinite molecular weight. These chains are made up of many repeating molecular units, known as repeat units, derived from monomers; each polymer chain will have several thousand repeating units. The vast majority of plastics are composed of polymers of carbon and hydrogen alone or with oxygen, nitrogen, chlorine or sulfur in the backbone. (Some of commercial interests are silicon based.) The backbone is that part of the chain on the main "path" linking a large number of repeat units together. To customize the properties of a plastic, different molecular groups "hang" from the backbone (usually they are "hung" as part of the monomers before linking monomers together to form the polymer chain). This fine tuning of the properties of the polymer by repeating unit’s molecular structure has allowed plastics to become such an indispensable part of twenty first-century world.

Some plastics are partially crystalline and partially amorphous in molecular structure, giving them both a melting point (the temperature at which the attractive intermolecular forces are overcome) and one or more glass transitions (temperatures above which the extent of localized molecular flexibility is substantially increased). The so-called semi-crystalline plastics include polyethylene, polypropylene, poly (vinyl chloride), polyamides (nylons), polyesters and some polyurethanes. Many plastics are completely amorphous, such as polystyrene and its copolymers, poly (methyl methacrylate), and all thermosets

History
The first human-made plastic was invented by Alexander Parkes in 1855 ; he called this plastic Parkesine (later called celluloid). It was unveiled at the 1862 Great International Exhibition in London. The development of plastics has come from the use of natural plastic materials (e.g., chewing gum, shellac) to the use of chemically modified natural materials (e.g., rubber, nitrocellulose, collagen, galalite) and finally to completely synthetic molecules (e.g., bakelite, epoxy, polyvinyl chloride, polyethylene

Types
Cellulose-based plastics
In 1855, an Englishman from Birmingham named Alexander Parkes developed a synthetic replacement for ivory which he marketed under the trade name Parkesine, and which won a bronze medal at the 1862 World’s fair in London. Parkesine was made from cellulose (the major component of plant cell walls) treated with nitric acid and a solvent. The output of the process (commonly known as cellulose nitrate or pyroxilin) could be dissolved in alcohol and hardened into a transparent and elastic material that could be molded when heated.[8] By incorporating pigments into the product, it could be made to resemble ivory.

Bois Durci is a plastic moulding material based on cellulose. It was patented in Paris by Lepage in 1855. It is made from finely ground wood flour mixed with a binder, either egg or blood albumen, or gelatine. The wood is probably either ebony or rose wood, which gives a black or brown resin. The mixture is dried and ground into a fine powder. The powder is placed in a steel mould and compressed in a powerful hydraulic press whilst being heated by steam. The final product has a highly polished finish imparted by the surface of the steel mould.
Bakelite
Main article: Bakelite
The first plastic based on a synthetic polymer was made from phenol and formaldehyde, with the first viable and cheap synthesis methods invented in 1909 by Leo Hendrik Baekeland, a Belgian-born American living in New York state. Baekeland was searching for an insulating shellac to coat wires in electric motors and generators. He found that mixtures of phenol (C6H5OH) and formaldehyde (HCOH) formed a sticky mass when mixed together and heated, and the mass became extremely hard if allowed to cool. He continued his investigations and found that the material could be mixed with wood flour, asbestos, or slate dust to create "composite" materials with different properties. Most of these compositions were strong and fire resistant. The only problem was that the material tended to foam during synthesis, and the resulting product was of unacceptable quality.

Baekeland built pressure vessels to force out the bubbles and provide a smooth, uniform product. He publicly announced his discovery in 1912, naming it bakelite. It was originally used for electrical and mechanical parts, finally coming into widespread use in consumer goods in the 1920s. When the Bakelite patent expired in 1930, the Catalin Corporation acquired the patent and began manufacturing Catalin plastic using a different process that allowed a wider range of coloring.

Bakelite was the first true plastic. It was a purely synthetic material, not based on any material or even molecule found in nature. It was also the first thermosetting plastic. Conventional thermoplastics can be molded and then melted again, but thermoset plastics form bonds between polymers strands when cured, creating a tangled matrix that cannot be undone without destroying the plastic. Thermoset plastics are tough and temperature resistant.

Bakelite was cheap, strong, and durable. It was molded into thousands of forms, such as cases for radios, telephones and clocks, and billiard balls. The U.S. government even considered making one-cent coins out of it when World War II caused a copper shortage.[citation needed]

Phenol-based ("Phenolic") plastics have been largely replaced by cheaper and less brittle plastics, but they are still used in applications requiring their insulating and heat-resistant properties. For example, some electronic circuit boards are made of sheets of paper or cloth impregnated with phenolic resin.

Phenolic sheets, rods and tubes are produced in a wide variety of grades under various brand names. The most common grades of industrial phenolic are Canvas, Linen and Paper.

Polystyrene and PVC

After the First World War, improvements in chemical technology led to an explosion in new forms of plastics. Among the earliest examples in the wave of new plastics were polystyrene (PS) and polyvinyl chloride (PVC), developed by IG Farben of Germany.

Polystyrene is a rigid, brittle, inexpensive plastic that has been used to make plastic model kits and similar knick-knacks. It would also be the basis for one of the most popular "foamed" plastics, under the name styrene foam or Styrofoam. Foam plastics can be synthesized in an "open cell" form, in which the foam bubbles are interconnected, as in an absorbent sponge, and "closed cell", in which all the bubbles are distinct, like tiny balloons, as in gas-filled foam insulation and flotation devices. In the late 1950s, high impact styrene was introduced, which was not brittle. It finds much current use as the substance of toy figurines and novelties.

Nylon
Main article: Nylon
The real star of the plastics industry in the 1930s was polyamide (PA), far better known by its trade name nylon. Nylon was the first purely synthetic fiber, introduced by DuPont Corporation at the 1939 World’s Fair in New York City.

In 1927, DuPont had begun a secret development project designated Fiber66, under the direction of Harvard chemist Wallace Carothers and chemistry department director Elmer Keiser Bolton. Carothers had been hired to perform pure research, and he worked to understand the new materials’ molecular structure and physical properties. He took some of the first steps in the molecular design of the materials.

His work led to the discovery of synthetic nylon fiber, which was very strong but also very flexible. The first application was for bristles for toothbrushes. However, Du Pont’s real target was silk, particularly silk stockings. Carothers and his team synthesized a number of different polyamides including polyamide 6.6 and 4.6, as well as polyesters.
It took DuPont twelve years and US million to refine nylon, and to synthesize and develop the industrial processes for bulk manufacture. With such a major investment, it was no surprise that Du Pont spared little expense to promote nylon after its introduction, creating a public sensation, or "nylon mania".

Nylon mania came to an abrupt stop at the end of 1941 when the USA entered World War II. The production capacity that had been built up to produce nylon stockings, or just nylons, for American women was taken over to manufacture vast numbers of parachutes for fliers and paratroopers. After the war ended, DuPont went back to selling nylon to the public, engaging in another promotional campaign in 1946 that resulted in an even bigger craze, triggering the so called nylon riots.

Subsequently polyamides 6, 10, 11, and 12 have been developed based on monomers which are ring compounds; e.g. caprolactam. Nylon 66 is a material manufactured by condensation polymerization.

Nylons still remain important plastics, and not just for use in fabrics. In its bulk form it is very wear resistant, particularly if oil-impregnated, and so is used to build gears, plain bearings, and because of good heat-resistance, increasingly for under-the-hood applications in cars, and other mechanical parts.
Toxicity
Due to their insolubility in water and relative chemical inertness, pure plastics generally have low toxicity in their finished state, and will pass through the digestive system with no ill effect (other than mechanical damage or obstruction). However, plastics often contain a variety of toxic additives. For example, plasticizers like adipates and phthalates are often added to brittle plastics like polyvinyl chloride (PVC) to make them pliable enough for use in food packaging, children’s toys and teethers, tubing, shower curtains and other items. Traces of these chemicals can leach out of the plastic when it comes into contact with food. Out of these concerns, the European Union has banned the use of DEHP (di-2-ethylhexyl phthalate), the most widely used plasticizer in PVC. Some compounds leaching from polystyrene food containers have been found to interfere with hormone functions and are suspected human carcinogens.

Moreover, while the finished plastic may be non-toxic, the monomers used in its manufacture may be toxic; and small amounts of those chemical may remain trapped in the product. The World Health Organization’s International Agency for Research on Cancer (IARC) has recognized the chemical used to make PVC, vinyl chloride, as a known human carcinogen. Some polymers may also decompose into the monomers or other toxic substances when heated.

The primary building block of polycarbonates, bisphenol A (BPA), is an estrogen-like endocrine disruptor that may leach into food. Research in Environmental Health Perspectives finds that BPA leached from the lining of tin cans, dental sealants and polycarbonate bottles can increase body weight of lab animals’ offspring.[11] A more recent animal study suggests that even low-level exposure to BPA results in insulin resistance, which can lead to inflammation and heart disease.

As of January 2010, the LA Times newspaper reports that the United States FDA is spending million to investigate suspicious indications of BPA being linked to cancer.

Bis(2-ethylhexyl) adipate, present in plastic wrap based on PVC, is also of concern, as are the volatile organic compounds present in new car smell.

The European Union has a permanent ban on on the use of phthalates in toys. In 2009, the United States government banned certain types of phthalates commonly used in plastic.
Environmental issues
Further information: Marine debris
Plastics are durable and degrade very slowly; the molecular bonds that make plastic so durable make it equally resistant to natural processes of degradation. Since the 1950s, one billion tons of plastic has been discarded and may persist for hundreds or even thousands of years. In some cases, burning plastic can release toxic fumes. Burning the plastic polyvinyl chloride (PVC) may create dioxin. Also, the manufacturing of plastics often creates large quantities of chemical pollutants.

Prior to the ban on the use of CFCs in extrusion of polystyrene (and general use, except in life-critical fire suppression systems; see Montreal Protocol), the production of polystyrene contributed to the depletion of the ozone layer; however, non-CFCs are currently used in the extrusion process.

By 1995, plastic recycling programs were common in the United States and elsewhere. Thermoplastics can be remelted and reused, and thermoset plastics can be ground up and used as filler, though the purity of the material tends to degrade with each reuse cycle. There are methods by which plastics can be broken back down to a feedstock state.

Plastic


Image by Joost J. Bakker IJmuiden
Plastic is the general common term for a wide range of synthetic or semisynthetic organic amorphous solid materials used in the manufacture of industrial products. Plastics are typically polymers of high molecular mass, and may contain other substances to improve performance and/or reduce costs. Monomers of Plastic are either natural or synthetic organic compounds.

The word is derived from the Greek πλαστικός (plastikos) meaning fit for molding, and πλαστός (plastos) meaning molded. It refers to their malleability, or plasticity during manufacture, that allows them to be cast, pressed, or extruded into a variety of shapes—such as films, fibers, plates, tubes, bottles, boxes, and much more.

The common word plastic should not be confused with the technical adjective plastic, which is applied to any material which undergoes a permanent change of shape (plastic deformation) when strained beyond a certain point. Aluminium, for instance, is plastic in this sense, but not a plastic in the common sense; in contrast, in their finished forms, some plastics will break before deforming and therefore are not plastic in the technical sense.

There are two types of plastics: thermoplastics and thermosetting polymers. Thermoplastics will soften and melt if enough heat is applied; examples are polyethylene, polystyrene, polyvinyl chloride and polytetrafluoroethylene (PTFE). Thermosets can melt and take shape once; after they have solidified, they

Plastics can be classified by chemical structure, namely the molecular units that make up the polymer’s backbone and side chains. Some important groups in these classifications are the acrylics, polyesters, silicones, polyurethanes, and halogenated plastics. Plastics can also be classified by the chemical process used in their synthesis, such as condensation, polyaddition, and cross-linking.

Other classifications are based on qualities that are relevant for manufacturing or product design. Examples of such classes are the thermoplastic and thermoset, elastomer, structural, biodegradable, and electrically conductive. Plastics can also be classified by various physical properties, such as density, tensile strength, glass transition temperature, and resistance to various chemical products.

Due to their relatively low cost, ease of manufacture, versatility, and imperviousness to water, plastics are used in an enormous and expanding range of products, from paper clips to spaceships. They have already displaced many traditional materials, such as wood; stone; horn and bone; leather; paper; metal; glass; and ceramic, in most of their former uses.

The use of plastics is constrained chiefly by their organic chemistry, which seriously limits their hardness, density, and their ability to resist heat, organic solvents, oxidation, and ionizing radiation. In particular, most plastics will melt or decompose when heated to a few hundred degrees celsius. While plastics can be made electrically conductive to some extent, they are still no match for metals like copper or aluminium.[citation needed] Plastics are still too expensive to replace wood, concrete and ceramic in bulky items like ordinary buildings, bridges, dams, pavement, and railroad ties.

Chemical structure
Common thermoplastics range from 20,000 to 500,000 in molecular mass, while thermosets are assumed to have infinite molecular weight. These chains are made up of many repeating molecular units, known as repeat units, derived from monomers; each polymer chain will have several thousand repeating units. The vast majority of plastics are composed of polymers of carbon and hydrogen alone or with oxygen, nitrogen, chlorine or sulfur in the backbone. (Some of commercial interests are silicon based.) The backbone is that part of the chain on the main "path" linking a large number of repeat units together. To customize the properties of a plastic, different molecular groups "hang" from the backbone (usually they are "hung" as part of the monomers before linking monomers together to form the polymer chain). This fine tuning of the properties of the polymer by repeating unit’s molecular structure has allowed plastics to become such an indispensable part of twenty first-century world.

Some plastics are partially crystalline and partially amorphous in molecular structure, giving them both a melting point (the temperature at which the attractive intermolecular forces are overcome) and one or more glass transitions (temperatures above which the extent of localized molecular flexibility is substantially increased). The so-called semi-crystalline plastics include polyethylene, polypropylene, poly (vinyl chloride), polyamides (nylons), polyesters and some polyurethanes. Many plastics are completely amorphous, such as polystyrene and its copolymers, poly (methyl methacrylate), and all thermosets

History
The first human-made plastic was invented by Alexander Parkes in 1855 ; he called this plastic Parkesine (later called celluloid). It was unveiled at the 1862 Great International Exhibition in London. The development of plastics has come from the use of natural plastic materials (e.g., chewing gum, shellac) to the use of chemically modified natural materials (e.g., rubber, nitrocellulose, collagen, galalite) and finally to completely synthetic molecules (e.g., bakelite, epoxy, polyvinyl chloride, polyethylene

Types
Cellulose-based plastics
In 1855, an Englishman from Birmingham named Alexander Parkes developed a synthetic replacement for ivory which he marketed under the trade name Parkesine, and which won a bronze medal at the 1862 World’s fair in London. Parkesine was made from cellulose (the major component of plant cell walls) treated with nitric acid and a solvent. The output of the process (commonly known as cellulose nitrate or pyroxilin) could be dissolved in alcohol and hardened into a transparent and elastic material that could be molded when heated.[8] By incorporating pigments into the product, it could be made to resemble ivory.

Bois Durci is a plastic moulding material based on cellulose. It was patented in Paris by Lepage in 1855. It is made from finely ground wood flour mixed with a binder, either egg or blood albumen, or gelatine. The wood is probably either ebony or rose wood, which gives a black or brown resin. The mixture is dried and ground into a fine powder. The powder is placed in a steel mould and compressed in a powerful hydraulic press whilst being heated by steam. The final product has a highly polished finish imparted by the surface of the steel mould.
Bakelite
Main article: Bakelite
The first plastic based on a synthetic polymer was made from phenol and formaldehyde, with the first viable and cheap synthesis methods invented in 1909 by Leo Hendrik Baekeland, a Belgian-born American living in New York state. Baekeland was searching for an insulating shellac to coat wires in electric motors and generators. He found that mixtures of phenol (C6H5OH) and formaldehyde (HCOH) formed a sticky mass when mixed together and heated, and the mass became extremely hard if allowed to cool. He continued his investigations and found that the material could be mixed with wood flour, asbestos, or slate dust to create "composite" materials with different properties. Most of these compositions were strong and fire resistant. The only problem was that the material tended to foam during synthesis, and the resulting product was of unacceptable quality.

Baekeland built pressure vessels to force out the bubbles and provide a smooth, uniform product. He publicly announced his discovery in 1912, naming it bakelite. It was originally used for electrical and mechanical parts, finally coming into widespread use in consumer goods in the 1920s. When the Bakelite patent expired in 1930, the Catalin Corporation acquired the patent and began manufacturing Catalin plastic using a different process that allowed a wider range of coloring.

Bakelite was the first true plastic. It was a purely synthetic material, not based on any material or even molecule found in nature. It was also the first thermosetting plastic. Conventional thermoplastics can be molded and then melted again, but thermoset plastics form bonds between polymers strands when cured, creating a tangled matrix that cannot be undone without destroying the plastic. Thermoset plastics are tough and temperature resistant.

Bakelite was cheap, strong, and durable. It was molded into thousands of forms, such as cases for radios, telephones and clocks, and billiard balls. The U.S. government even considered making one-cent coins out of it when World War II caused a copper shortage.[citation needed]

Phenol-based ("Phenolic") plastics have been largely replaced by cheaper and less brittle plastics, but they are still used in applications requiring their insulating and heat-resistant properties. For example, some electronic circuit boards are made of sheets of paper or cloth impregnated with phenolic resin.

Phenolic sheets, rods and tubes are produced in a wide variety of grades under various brand names. The most common grades of industrial phenolic are Canvas, Linen and Paper.

Polystyrene and PVC

After the First World War, improvements in chemical technology led to an explosion in new forms of plastics. Among the earliest examples in the wave of new plastics were polystyrene (PS) and polyvinyl chloride (PVC), developed by IG Farben of Germany.

Polystyrene is a rigid, brittle, inexpensive plastic that has been used to make plastic model kits and similar knick-knacks. It would also be the basis for one of the most popular "foamed" plastics, under the name styrene foam or Styrofoam. Foam plastics can be synthesized in an "open cell" form, in which the foam bubbles are interconnected, as in an absorbent sponge, and "closed cell", in which all the bubbles are distinct, like tiny balloons, as in gas-filled foam insulation and flotation devices. In the late 1950s, high impact styrene was introduced, which was not brittle. It finds much current use as the substance of toy figurines and novelties.

Nylon
Main article: Nylon
The real star of the plastics industry in the 1930s was polyamide (PA), far better known by its trade name nylon. Nylon was the first purely synthetic fiber, introduced by DuPont Corporation at the 1939 World’s Fair in New York City.

In 1927, DuPont had begun a secret development project designated Fiber66, under the direction of Harvard chemist Wallace Carothers and chemistry department director Elmer Keiser Bolton. Carothers had been hired to perform pure research, and he worked to understand the new materials’ molecular structure and physical properties. He took some of the first steps in the molecular design of the materials.

His work led to the discovery of synthetic nylon fiber, which was very strong but also very flexible. The first application was for bristles for toothbrushes. However, Du Pont’s real target was silk, particularly silk stockings. Carothers and his team synthesized a number of different polyamides including polyamide 6.6 and 4.6, as well as polyesters.
It took DuPont twelve years and US million to refine nylon, and to synthesize and develop the industrial processes for bulk manufacture. With such a major investment, it was no surprise that Du Pont spared little expense to promote nylon after its introduction, creating a public sensation, or "nylon mania".

Nylon mania came to an abrupt stop at the end of 1941 when the USA entered World War II. The production capacity that had been built up to produce nylon stockings, or just nylons, for American women was taken over to manufacture vast numbers of parachutes for fliers and paratroopers. After the war ended, DuPont went back to selling nylon to the public, engaging in another promotional campaign in 1946 that resulted in an even bigger craze, triggering the so called nylon riots.

Subsequently polyamides 6, 10, 11, and 12 have been developed based on monomers which are ring compounds; e.g. caprolactam. Nylon 66 is a material manufactured by condensation polymerization.

Nylons still remain important plastics, and not just for use in fabrics. In its bulk form it is very wear resistant, particularly if oil-impregnated, and so is used to build gears, plain bearings, and because of good heat-resistance, increasingly for under-the-hood applications in cars, and other mechanical parts.
Toxicity
Due to their insolubility in water and relative chemical inertness, pure plastics generally have low toxicity in their finished state, and will pass through the digestive system with no ill effect (other than mechanical damage or obstruction). However, plastics often contain a variety of toxic additives. For example, plasticizers like adipates and phthalates are often added to brittle plastics like polyvinyl chloride (PVC) to make them pliable enough for use in food packaging, children’s toys and teethers, tubing, shower curtains and other items. Traces of these chemicals can leach out of the plastic when it comes into contact with food. Out of these concerns, the European Union has banned the use of DEHP (di-2-ethylhexyl phthalate), the most widely used plasticizer in PVC. Some compounds leaching from polystyrene food containers have been found to interfere with hormone functions and are suspected human carcinogens.

Moreover, while the finished plastic may be non-toxic, the monomers used in its manufacture may be toxic; and small amounts of those chemical may remain trapped in the product. The World Health Organization’s International Agency for Research on Cancer (IARC) has recognized the chemical used to make PVC, vinyl chloride, as a known human carcinogen. Some polymers may also decompose into the monomers or other toxic substances when heated.

The primary building block of polycarbonates, bisphenol A (BPA), is an estrogen-like endocrine disruptor that may leach into food. Research in Environmental Health Perspectives finds that BPA leached from the lining of tin cans, dental sealants and polycarbonate bottles can increase body weight of lab animals’ offspring.[11] A more recent animal study suggests that even low-level exposure to BPA results in insulin resistance, which can lead to inflammation and heart disease.

As of January 2010, the LA Times newspaper reports that the United States FDA is spending million to investigate suspicious indications of BPA being linked to cancer.

Bis(2-ethylhexyl) adipate, present in plastic wrap based on PVC, is also of concern, as are the volatile organic compounds present in new car smell.

The European Union has a permanent ban on on the use of phthalates in toys. In 2009, the United States government banned certain types of phthalates commonly used in plastic.
Environmental issues
Further information: Marine debris
Plastics are durable and degrade very slowly; the molecular bonds that make plastic so durable make it equally resistant to natural processes of degradation. Since the 1950s, one billion tons of plastic has been discarded and may persist for hundreds or even thousands of years. In some cases, burning plastic can release toxic fumes. Burning the plastic polyvinyl chloride (PVC) may create dioxin. Also, the manufacturing of plastics often creates large quantities of chemical pollutants.

Prior to the ban on the use of CFCs in extrusion of polystyrene (and general use, except in life-critical fire suppression systems; see Montreal Protocol), the production of polystyrene contributed to the depletion of the ozone layer; however, non-CFCs are currently used in the extrusion process.

By 1995, plastic recycling programs were common in the United States and elsewhere. Thermoplastics can be remelted and reused, and thermoset plastics can be ground up and used as filler, though the purity of the material tends to degrade with each reuse cycle. There are methods by which plastics can be broken back down to a feedstock state.

Ain’t No Stopping Me Now

Price: $ 0.99

Related Facebook pages

steam cells pages

Related Twitter topic

steam cells topics

Related Flicker images

steam cells images

Related youtube videos

steam cells videos

www.pbs.org – The human face of stem cell research: a neurologist seeks a cure for his paralyzed teenage daughter.
Video Rating: 4 / 5

2bsteam

Price: $ 8.91

A match made in heaven…


Image by quirkyrocket ❤
Seriously, you cannot go wrong with a giant blushing plushy jam-bun hanging off your phone.

Related Facebook pages

steam cells pages

Related Twitter topic

steam cells topics

Related Flicker images

steam cells images

Related youtube videos

steam cells videos

• Take the battle online, experiencing large scale multiplayer action like never before in epic infantry and vehicle warfare
• Discover a terrifyingly plausible near-future world in which the familiar has become alien in this nightmare vision of Occupied USA
• Fight for a cause joining a cast of memorable characters as your resistance cell wages a guerrilla war against overwhelming military odds in the name of Freedom
• Witness the human cost of war in a gripping story from the pen of John Milius is told through immersive, interactive 1st person cut scenes
• Experience explosive FPS gameplay as you battle through a dynamic mix of infantry and vehicle combat in a gripping single player campaign boasting intense, memorable set pieces

The year is 2027. The world as we know it is unraveling after fifteen years of economic meltdown and widespread global conflict over dwindling natural resources. A once proud America has fallen, her infrastructure shattered and military in disarray. The USA is powerless to resist the ever expanding occupation of a savage, nuclear armed Greater Korean Republic. Homefront is a first-person shooter that challenges players to survive and impact a fictional future scenario in which America has been

List Price: $ 29.99

Price: $ 9.59

Run-in with a steam wand


Image by NancyKay69
Burned my arm on an espresso machine steam wand while helping in the cafe at work. Picture taken with LG cell phone

More Steam Cells Products

Related Facebook pages

steam cells pages

Related Twitter topic

steam cells topics

Related Flicker images

steam cells images

Related youtube videos

steam cells videos

Some curiosity has been excited, during several weeks past, by the performances on the Thames of a small launch, named the Electricity, which is propelled by electric power, instead of by steam. The little vessel, when not in motion, has usually been seen lying at her mooring off the wharf of the works of the Electrical Power Storage Company at Millwall. This boat, which was designed by Mr. Reckenzaun, is 26 ft. in length and about 5 ft. in the beam, drawing about 2 ft. of water, and fitted with a 22-inch propeller screw. She carries, under the flooring and seats, fore and aft, forty-five mysterious boxes, each a cube of about l0in. in dimensions. These boxes are nothing else than electric accumulators of the latest type as devised by Messrs. Sellon and Volckmar, being a modification of the well known Planté accumulator. Fully charged with electricity by wires leading from the dynamos or generators in the works, they are calculated to supply power for six hours tit the rate of four horse-power. These storage cells are placed in electrical connection with two Siemens’ dynamos of the size known as D 3, furnished with proper reversing-gear and regulators, to serve as engines to drive the screw propeller. Either or both of these motors can be "switched" into circuit at will. In charge of the electric engines is Mr. Gustave Phillipart, jun., who has been associated with Mr. Volckmar in the fitting up of the electric launch. Mr. Sylvanus Thompson, who made a short trip in her on the 28th ult., describes her performance as quite satisfactory, with a speed of eight knots an hour against the tide, and with sufficient handiness of evolution. He adds, for the benefit of electricians, that the total electro-motive force of the accumulators was 96 volts, and that during the whole of the long run the current through each machine was steadily maintained at 24 ampères. Calculations show that this corresponds to an expenditure of electric energy at the rate of three and one-eleventh horse horse-power. It is now forty-three years since the Russian Jacobi first propelled a boat upon the waters of the Nova by aid of a largo but primitive electro-magnetic engine, worked by galvanic batteries of the old type, wherein zinc plates were dissolved in acid.Two years ago a little model boat was shown fit Paris by M. Trouvé, propelled by accumulators of the Faure-Planté type. The present is, however not only the first electric boat that has been constructed in this country, but the very first in which the electric propulsion of a boat has been undertaken on a commercial scale.

Gustave Phillipart, one of the men on the boat, also invented the diabolo, a toy in which a spool is spun along a cord attached to two hand-held sticks which is sometimes known as "the devil on two sticks".

I have a dream


Image by Frank Kehren

I am happy to join with you today in what will go down in history as the greatest demonstration for freedom in the history of our nation.

8/28/1963, Lincoln Memorial, Washington DC

Missing You

Price: $ 0.99

Related Facebook pages

steam cells pages

Related Twitter topic

steam cells topics

Related Flicker images

steam cells images

Related youtube videos

steam cells videos